Xilinx Zynq MP First Stage Boot Loader Release 2018.3 Jan 25 2019 - 10:59:32 NOTICE: ATF running on XCZU28DR/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: Secure code at 0x0 NOTICE: BL31: Non secure code at 0x8000000 NOTICE: BL31: v1.5(release):xilinx-v2018.2-919-g08560c36 NOTICE: BL31: Built : 10:58:53, Jan 25 2019 PMUFW: v1.1 U-Boot 2018.01 (Jan 25 2019 - 10:57:43 +0000) Xilinx ZynqMP ZCU111 I2C: ready DRAM: 4 GiB EL Level: EL2 Chip ID: zu28dr MMC: sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms. sdhci_send_command: MMC: 0 busy timeout increasing to: 400 ms. sdhci_send_command: MMC: 0 busy timeout increasing to: 800 ms. sdhci_send_command: MMC: 0 busy timeout increasing to: 1600 ms. sdhci_send_command: MMC: 0 busy timeout increasing to: 3200 ms. sdhci_send_command: MMC: 0 busy timeout. sdhci_send_command: MMC: 0 busy timeout. mmc_init: -70, time 7439 mmc@ff170000 - probe failed: -70 sdhci_send_command: MMC: 0 busy timeout. sdhci_send_command: MMC: 0 busy timeout. mmc_init: -70, time 7413 SF: Detected mt25qu02g with page size 512 Bytes, erase size 128 KiB, total 512 MiB In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Model: ZynqMP ZCU111 RevA Board: Xilinx ZynqMP Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> ZynqMP> tftpboot 0x5000000 rootfs.jffs2 Using ethernet@ff0e0000 device TFTP from server 192.168.168.15; our IP address is 192.168.168.10 Filename 'rootfs.jffs2'. Load address: 0x5000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 2.7 MiB/s done Bytes transferred = 9420800 (8fc000 hex) ZynqMP> sf erase 0x4d00000 0x2000000 No SPI flash selected. Please run `sf probe' ZynqMP> sf probe SF: Detected mt25qu02g with page size 512 Bytes, erase size 128 KiB, total 512 MiB ZynqMP> sf erase 0x4d00000 0x2000000 SF: 33554432 bytes @ 0x4d00000 Erased: OK ZynqMP> sf write 0x5000000 0x4d00000 0x8fc000 device 0 offset 0x4d00000, size 0x8fc000 SF: 9420800 bytes @ 0x4d00000 Written: OK ZynqMP> boot SF: Detected mt25qu02g with page size 512 Bytes, erase size 128 KiB, total 512 MiB device 0 offset 0x2900000, size 0x2400000 SF: 37748736 bytes @ 0x2900000 Read: OK ## Loading kernel from FIT Image at 03000000 ... Using 'conf@system-top.dtb' configuration Trying 'kernel@1' kernel subimage Description: Linux kernel Type: Kernel Image Compression: gzip compressed Data Start: 0x03000108 Data Size: 7083891 Bytes = 6.8 MiB Architecture: AArch64 OS: Linux Load Address: 0x00080000 Entry Point: 0x00080000 Hash algo: sha1 Hash value: 55b1df062ba3c745ec43c677e2fb2e43b9037ef8 Verifying Hash Integrity ... sha1+ OK ## Loading fdt from FIT Image at 03000000 ... Using 'conf@system-top.dtb' configuration Trying 'fdt@system-top.dtb' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x036c1980 Data Size: 46614 Bytes = 45.5 KiB Architecture: AArch64 Hash algo: sha1 Hash value: c6865f23c1a03400eca58c7094bd3dad6deb1386 Verifying Hash Integrity ... sha1+ OK Booting using the fdt blob at 0x36c1980 Uncompressing Kernel Image ... OK Loading Device Tree to 0000000007ff1000, end 0000000007fff615 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-xilinx-v2018.3 (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP Fri Jan 25 11:03:19 UTC 2019 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Machine model: ZynqMP ZCU111 RevA [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] bootconsole [cdns0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000006fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff61000 s46488 r8192 d31336 u86016 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1033987 [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=mtd:jffs2 rw rootfstype=jffs2 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff] [ 0.000000] Memory: 3784236K/4193280K available (10108K kernel code, 664K rwdata, 3224K rodata, 512K init, 2167K bss, 146900K reserved, 262144K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a60000 ( 10112 KB) [ 0.000000] .rodata : 0xffffff8008a60000 - 0xffffff8008d90000 ( 3264 KB) [ 0.000000] .init : 0xffffff8008d90000 - 0xffffff8008e10000 ( 512 KB) [ 0.000000] .data : 0xffffff8008e10000 - 0xffffff8008eb6200 ( 665 KB) [ 0.000000] .bss : 0xffffff8008eb6200 - 0xffffff80090d40b0 ( 2168 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf1dc00000 ( 476 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc880000000 ( 34816 MB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@a00c2000: num_irq=2, edge=0x3 [ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171015c90f, max_idle_ns: 440795203080 ns [ 0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns [ 0.008318] Console: colour dummy device 80x25 [ 0.012388] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.99 BogoMIPS (lpj=399996) [ 0.022754] pid_max: default: 32768 minimum: 301 [ 0.027437] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.034009] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.041665] ASID allocator initialised with 65536 entries [ 0.046504] Hierarchical SRCU implementation. [ 0.051113] EFI services will not be available. [ 0.055297] zynqmp_plat_init Platform Management API v1.1 [ 0.060643] zynqmp_plat_init Trustzone version v1.0 [ 0.065583] smp: Bringing up secondary CPUs ... [ 0.252077] Detected VIPT I-cache on CPU1 [ 0.252106] CPU1: Booted secondary processor [410fd034] [ 0.391585] Detected VIPT I-cache on CPU2 [ 0.391603] CPU2: Booted secondary processor [410fd034] [ 0.520230] Detected VIPT I-cache on CPU3 [ 0.520248] CPU3: Booted secondary processor [410fd034] [ 0.520290] smp: Brought up 1 node, 4 CPUs [ 0.546257] SMP: Total of 4 processors activated. [ 0.550930] CPU features: detected feature: 32-bit EL0 Support [ 0.556728] CPU: All CPU(s) started at EL2 [ 0.560799] alternatives: patching kernel code [ 0.565945] devtmpfs: initialized [ 0.573353] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.578184] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.589867] xor: measuring software checksum speed [ 0.628477] 8regs : 2303.000 MB/sec [ 0.668506] 8regs_prefetch: 2053.000 MB/sec [ 0.708534] 32regs : 2830.000 MB/sec [ 0.748565] 32regs_prefetch: 2379.000 MB/sec [ 0.748593] xor: using function: 32regs (2830.000 MB/sec) [ 0.752971] pinctrl core: initialized pinctrl subsystem [ 0.758584] NET: Registered protocol family 16 [ 0.763115] cpuidle: using governor menu [ 0.766960] vdso: 2 pages (1 code @ ffffff8008a66000, 1 data @ ffffff8008e14000) [ 0.773761] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.780952] DMA: preallocated 256 KiB pool for atomic allocations [ 0.807975] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed [ 0.809894] ARM CCI_400_r1 PMU driver probed [ 0.814578] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized [ 0.829321] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.898296] raid6: int64x1 gen() 401 MB/s [ 0.966330] raid6: int64x1 xor() 446 MB/s [ 1.034380] raid6: int64x2 gen() 688 MB/s [ 1.102431] raid6: int64x2 xor() 603 MB/s [ 1.170458] raid6: int64x4 gen() 1042 MB/s [ 1.238499] raid6: int64x4 xor() 740 MB/s [ 1.306562] raid6: int64x8 gen() 980 MB/s [ 1.374581] raid6: int64x8 xor() 745 MB/s [ 1.442675] raid6: neonx1 gen() 726 MB/s [ 1.510687] raid6: neonx1 xor() 853 MB/s [ 1.578765] raid6: neonx2 gen() 1168 MB/s [ 1.646787] raid6: neonx2 xor() 1202 MB/s [ 1.714823] raid6: neonx4 gen() 1503 MB/s [ 1.782882] raid6: neonx4 xor() 1437 MB/s [ 1.850930] raid6: neonx8 gen() 1649 MB/s [ 1.918966] raid6: neonx8 xor() 1525 MB/s [ 1.918993] raid6: using algorithm neonx8 gen() 1649 MB/s [ 1.922960] raid6: .... xor() 1525 MB/s, rmw enabled [ 1.927891] raid6: using neon recovery algorithm [ 1.932992] XGpio: /amba_pl@0/gpio@a00c0000: registered, base is 507 [ 1.939142] XGpio: /amba_pl@0/gpio@a00c1000: registered, base is 499 [ 1.946455] SCSI subsystem initialized [ 1.948983] usbcore: registered new interface driver usbfs [ 1.954318] usbcore: registered new interface driver hub [ 1.959589] usbcore: registered new device driver usb [ 1.964622] media: Linux media interface: v0.10 [ 1.969084] Linux video capture interface: v2.00 [ 1.973680] pps_core: LinuxPPS API ver. 1 registered [ 1.978581] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.987672] PTP clock support registered [ 1.991570] EDAC MC: Ver: 3.0.0 [ 1.995267] zynqmp-ipi ff9905c0.mailbox: Probed ZynqMP IPI Mailbox driver. [ 2.001772] FPGA manager framework [ 2.004969] fpga-region fpga-full: FPGA Region probed [ 2.009990] Advanced Linux Sound Architecture Driver Initialized. [ 2.016183] Bluetooth: Core ver 2.22 [ 2.019509] NET: Registered protocol family 31 [ 2.023909] Bluetooth: HCI device and connection manager initialized [ 2.030227] Bluetooth: HCI socket layer initialized [ 2.035069] Bluetooth: L2CAP socket layer initialized [ 2.040098] Bluetooth: SCO socket layer initialized [ 2.045474] clocksource: Switched to clocksource arch_sys_counter [ 2.051040] VFS: Disk quotas dquot_6.6.0 [ 2.054931] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.066502] NET: Registered protocol family 2 [ 2.066817] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 2.073416] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 2.080190] TCP: Hash tables configured (established 32768 bind 32768) [ 2.086342] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 2.092313] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 2.098784] NET: Registered protocol family 1 [ 2.103146] RPC: Registered named UNIX socket transport module. [ 2.108861] RPC: Registered udp transport module. [ 2.113522] RPC: Registered tcp transport module. [ 2.118194] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.125049] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.131852] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 2.140057] audit: initializing netlink subsys (disabled) [ 2.144825] audit: type=2000 audit(2.080:1): state=initialized audit_enabled=0 res=1 [ 2.145130] workingset: timestamp_bits=62 max_order=20 bucket_order=0 [ 2.159453] NFS: Registering the id_resolver key type [ 2.163882] Key type id_resolver registered [ 2.168020] Key type id_legacy registered [ 2.172003] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.178671] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 2.208082] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.209837] io scheduler noop registered [ 2.213718] io scheduler deadline registered [ 2.217967] io scheduler cfq registered (default) [ 2.222627] io scheduler mq-deadline registered [ 2.227124] io scheduler kyber registered [ 2.232350] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed [ 2.237829] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 2.244485] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 2.251409] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 2.258328] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 2.265246] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 2.272164] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 2.279093] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 2.286006] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 2.292991] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 2.299844] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 2.306765] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 2.313688] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 2.320604] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 2.327525] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 2.334448] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 2.341367] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 2.372870] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.376925] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 2.383749] brd: module loaded [ 2.387012] loop: module loaded [ 2.387556] xilinx-sdfec a0080000.sd-fec: XSDFEC0 Probe Successful [ 2.392216] xilinx-sdfec a0040000.sd-fec: XSDFEC1 Probe Successful [ 2.398667] ahci-ceva fd0c0000.ahci: couldn't get PHY in node ahci: -517 [ 2.404897] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.411952] m25p80 spi0.0: found mt25ul02g, expected n25q512a [ 2.417039] m25p80 spi0.0: mt25ul02g (524288 Kbytes) [ 2.421786] 4 ofpart partitions found on MTD device spi0.0 [ 2.427211] Creating 4 MTD partitions on "spi0.0": [ 2.431973] 0x000000000000-0x000002800000 : "boot" [ 2.437162] 0x000002800000-0x000002900000 : "bootenv" [ 2.442174] 0x000002900000-0x000004d00000 : "kernel" [ 2.447036] 0x000004d00000-0x000006d00000 : "jffs2" [ 2.452701] libphy: Fixed MDIO Bus: probed [ 2.456502] tun: Universal TUN/TAP device driver, 1.6 [ 2.460725] CAN device driver interface [ 2.465858] macb ff0e0000.ethernet: Not enabling partial store and forward [ 2.471665] libphy: MACB_mii_bus: probed [ 2.475623] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 31 (00:0a:35:00:22:01) [ 2.484915] TI DP83867 ff0e0000.ethernet-ffffffff:0c: attached PHY driver [TI DP83867] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:0c, irq=POLL) [ 2.498514] usbcore: registered new interface driver asix [ 2.503289] usbcore: registered new interface driver ax88179_178a [ 2.509322] usbcore: registered new interface driver cdc_ether [ 2.515117] usbcore: registered new interface driver net1080 [ 2.520739] usbcore: registered new interface driver cdc_subset [ 2.526621] usbcore: registered new interface driver zaurus [ 2.532167] usbcore: registered new interface driver cdc_ncm [ 2.538019] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 2.545274] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.550476] ehci-pci: EHCI PCI platform driver [ 2.555171] usbcore: registered new interface driver uas [ 2.560195] usbcore: registered new interface driver usb-storage [ 2.566608] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0 [ 2.573366] i2c /dev entries driver [ 2.577775] IR NEC protocol handler initialized [ 2.581263] IR RC5(x/sz) protocol handler initialized [ 2.586287] IR RC6 protocol handler initialized [ 2.590784] IR JVC protocol handler initialized [ 2.595280] IR Sony protocol handler initialized [ 2.599865] IR SANYO protocol handler initialized [ 2.604539] IR Sharp protocol handler initialized [ 2.609207] IR MCE Keyboard/mouse protocol handler initialized [ 2.615002] IR XMP protocol handler initialized [ 2.620944] usbcore: registered new interface driver uvcvideo [ 2.625211] USB Video Class driver (1.1.1) [ 2.629919] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff800916d000 with timeout 60s [ 2.638350] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer at ffffff8009175000 with timeout 10s [ 2.647292] Bluetooth: HCI UART driver ver 2.3 [ 2.651511] Bluetooth: HCI UART protocol H4 registered [ 2.656610] Bluetooth: HCI UART protocol BCSP registered [ 2.661907] Bluetooth: HCI UART protocol LL registered [ 2.666991] Bluetooth: HCI UART protocol ATH3K registered [ 2.672353] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.678619] Bluetooth: HCI UART protocol Intel registered [ 2.683945] Bluetooth: HCI UART protocol QCA registered [ 2.689167] usbcore: registered new interface driver bcm203x [ 2.694782] usbcore: registered new interface driver bpa10x [ 2.700320] usbcore: registered new interface driver bfusb [ 2.705768] usbcore: registered new interface driver btusb [ 2.711193] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 2.716854] usbcore: registered new interface driver ath3k [ 2.722385] EDAC MC: ECC not enabled [ 2.725975] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 2.738787] sdhci: Secure Digital Host Controller Interface driver [ 2.744064] sdhci: Copyright(c) Pierre Ossman [ 2.748387] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.797488] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 2.806434] ledtrig-cpu: registered to indicate activity on CPUs [ 2.806918] usbcore: registered new interface driver usbhid [ 2.812331] usbhid: USB HID core driver [ 2.817940] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 2.822902] usbcore: registered new interface driver snd-usb-audio [ 2.829456] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 2.836401] Netfilter messages via NETLINK v0.30. [ 2.840984] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.846280] Initializing XFRM netlink socket [ 2.850445] NET: Registered protocol family 10 [ 2.855201] Segment Routing with IPv6 [ 2.858477] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.863910] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.869983] NET: Registered protocol family 17 [ 2.874100] NET: Registered protocol family 15 [ 2.878514] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.891393] Ebtables v2.0 registered [ 2.895015] can: controller area network core (rev 20170425 abi 9) [ 2.901107] NET: Registered protocol family 29 [ 2.905495] can: raw protocol (rev 20170425) [ 2.909731] can: broadcast manager protocol (rev 20170425 t) [ 2.915356] can: netlink gateway (rev 20170425) max_hops=1 [ 2.920856] Bluetooth: RFCOMM TTY layer initialized [ 2.925651] Bluetooth: RFCOMM socket layer initialized [ 2.930756] Bluetooth: RFCOMM ver 1.11 [ 2.934471] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.939747] Bluetooth: BNEP filters: protocol multicast [ 2.944937] Bluetooth: BNEP socket layer initialized [ 2.949866] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.955749] Bluetooth: HIDP socket layer initialized [ 2.960788] 9pnet: Installing 9P2000 support [ 2.964929] Key type dns_resolver registered [ 2.969703] registered taskstats version 1 [ 2.973531] Btrfs loaded, crc32c=crc32c-generic ½¹Í½±?¹ÍÁê"¥ÍÑÑå±5RÚr²ê2Jr?±é¢ÑåAMŹͽ±ÚÑÑåAMÁê*¹ff00000±5RÚrÊʪ¢ºê½½Ñse_baud = 6249999) is a xuartps ?j5%=?JBJÉÅê¢b?} ?ê²¢ÊÊÊÊJJ? ÂÕÉÑÁÍ5Rþ[ 3.017943] xilinx-psgtr fd400000.zynqmp_phy: Lane:1 type:8 protocol:4 pll_locked:yes [ 3.026112] PLL: shutdown [ 3.028814] PLL: shutdown [ 3.031799] PLL: enable [ 3.034344] PLL: shutdown [ 3.037896] PLL: enable [ 3.040420] xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed [ 3.051077] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed [ 3.059101] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed [ 3.067381] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 3.079813] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 3.092499] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed [ 3.102673] OF: graph: no port node found in /amba/zynqmp-display@fd4a0000 [ 3.109654] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.116256] [drm] No driver support for vblank timestamp query. [ 3.122225] xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8008b17868) [ 4.209486] [drm] Cannot find any crtc or sizes [ 4.266778] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0 [ 4.274877] zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsystem driver probed [ 4.283839] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:3 protocol:2 pll_locked:yes [ 4.301780] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 4.310739] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 4.321018] scsi host0: ahci-ceva [ 4.324521] scsi host1: ahci-ceva [ 4.327933] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 40 [ 4.335845] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 40 [ 4.345497] xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes [ 4.355565] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.361053] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 4.368911] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x22010810 [ 4.377633] xhci-hcd xhci-hcd.0.auto: irq 64, io mem 0xfe200000 [ 4.383656] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.390437] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.397646] usb usb1: Product: xHCI Host Controller [ 4.402515] usb usb1: Manufacturer: Linux 4.14.0-xilinx-v2018.3 xhci-hcd [ 4.409207] usb usb1: SerialNumber: xhci-hcd.0.auto [ 4.414339] hub 1-0:1.0: USB hub found [ 4.418099] hub 1-0:1.0: 1 port detected [ 4.422179] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.427661] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 4.435433] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.442214] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.449427] usb usb2: Product: xHCI Host Controller [ 4.454303] usb usb2: Manufacturer: Linux 4.14.0-xilinx-v2018.3 xhci-hcd [ 4.460993] usb usb2: SerialNumber: xhci-hcd.0.auto [ 4.466094] hub 2-0:1.0: USB hub found [ 4.469856] hub 2-0:1.0: 1 port detected [ 4.474838] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator [ 4.484844] pca953x 0-0020: interrupt support not compiled in [ 4.491372] ina2xx 3-0040: power monitor ina226 (Rshunt = 2000 uOhm) [ 4.498136] ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.504902] ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.511681] ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.518455] ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.525213] ina2xx 3-0046: power monitor ina226 (Rshunt = 2000 uOhm) [ 4.531990] ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.538751] ina2xx 3-0048: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.545525] ina2xx 3-0049: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.552293] ina2xx 3-004a: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.559067] ina2xx 3-004b: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.565843] ina2xx 3-004c: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.572612] ina2xx 3-004d: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.579377] ina2xx 3-004e: power monitor ina226 (Rshunt = 5000 uOhm) [ 4.585759] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.590686] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.595775] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.600687] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.605479] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544 [ 4.612804] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 33 [ 4.620351] at24 7-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write [ 4.627071] i2c i2c-1: Added multiplexed i2c bus 7 [ 4.632044] i2c i2c-1: Added multiplexed i2c bus 8 [ 4.638885] si570 9-005d: registered, current frequency 300000000 Hz [ 4.645256] i2c i2c-1: Added multiplexed i2c bus 9 [ 4.655666] ata1: SATA link down (SStatus 0 SControl 330) [ 4.661092] ata2: SATA link down (SStatus 0 SControl 330) [ 4.664020] si570 10-005d: registered, current frequency 148500000 Hz [ 4.664050] i2c i2c-1: Added multiplexed i2c bus 10 [ 4.669623] si5324 11-0069: si5328 probed [ 4.725529] si5324 11-0069: unable to read from reg00 [ 4.731732] si5324 11-0069: si5328 probe successful [ 4.736635] i2c i2c-1: Added multiplexed i2c bus 11 [ 4.741699] i2c i2c-1: Added multiplexed i2c bus 12 [ 4.746694] i2c i2c-1: Added multiplexed i2c bus 13 [ 4.751680] i2c i2c-1: Added multiplexed i2c bus 14 [ 4.756553] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548 [ 4.764424] i2c i2c-1: Added multiplexed i2c bus 15 [ 4.769418] i2c i2c-1: Added multiplexed i2c bus 16 [ 4.774409] i2c i2c-1: Added multiplexed i2c bus 17 [ 4.779699] i2c i2c-1: Added multiplexed i2c bus 18 [ 4.784702] i2c i2c-1: Added multiplexed i2c bus 19 [ 4.789693] i2c i2c-1: Added multiplexed i2c bus 20 [ 4.794686] i2c i2c-1: Added multiplexed i2c bus 21 [ 4.799674] i2c i2c-1: Added multiplexed i2c bus 22 [ 4.804546] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548 [ 4.812124] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 34 [ 4.819223] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.826127] rtc_zynqmp ffa60000.rtc: setting system clock to 2019-01-25 11:50:51 UTC (1548417051) [ 4.834996] of_cfs_init [ 4.837442] of_cfs_init: OK [ 4.840356] clk: Not disabling unused clocks [ 4.844836] ALSA device list: [ 4.847793] #0: DisplayPort monitor [ 5.030410] random: crng init done [ 5.301492] [drm] Cannot find any crtc or sizes [ 5.492275] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.518172] VFS: Mounted root (jffs2 filesystem) on device 31:3. [ 5.524465] devtmpfs: mounted [ 5.527540] Freeing unused kernel memory: 512K INIT: version 2.88 booting Starting udev [ 6.364232] udevd[1882]: starting version 3.2.2 [ 6.425374] udevd[1883]: starting eudev-3.2.2 Starting internet superserver: inetd. Configuring packages on first boot.... (This may take several minutes. Please do not power off the machine.) Running postinst /etc/rpm-postinsts/100-sysvinit-inittab... update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing) Removing any system startup links for run-postinsts ... /etc/rcS.d/S99run-postinsts INIT: Entering runlevel: 5 Configuring network interfaces... [ 7.450347] pps pps0: new PPS source ptp0 [ 7.454368] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered. [ 7.461049] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.24.1) started Sending discover... [ 8.473601] macb ff0e0000.ethernet eth0: link up (1000/Full) [ 8.479269] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... [ 12.485484] m25p80 spi0.0: SPI transfer timed out [ 12.490190] m25p80 spi0.0: error -110 reading 5 [ 12.494715] error -110 reading SR [ 12.498023] jffs2: error: (2062) read_more: can not read 28 bytes from 0x008eb9c4, error code: -110. [ 12.507145] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 1166, returned error is -110 [ 12.517742] jffs2: Returned error for crccheck of ino #1166. Expect badness... [ 12.859180] m25p80 spi0.0: SPI transfer timed out [ 12.863885] m25p80 spi0.0: error -110 reading 5 [ 12.868409] error -110 reading SR [ 12.871717] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x0010cb8c, error code: -110. [ 12.881882] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 143, returned error is -110 [ 12.892399] jffs2: Returned error for crccheck of ino #143. Expect badness... [ 13.157482] m25p80 spi0.0: SPI transfer timed out [ 13.162183] m25p80 spi0.0: error -110 reading 5 [ 13.166700] error -110 reading SR [ 13.170010] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x00119870, error code: -110. [ 13.180173] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 271, returned error is -110 [ 13.190684] jffs2: Returned error for crccheck of ino #271. Expect badness... [ 13.457481] m25p80 spi0.0: SPI transfer timed out [ 13.462184] m25p80 spi0.0: error -110 reading 5 [ 13.466702] error -110 reading SR [ 13.470009] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x002cef98, error code: -110. [ 13.480173] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 399, returned error is -110 [ 13.490684] jffs2: Returned error for crccheck of ino #399. Expect badness... [ 13.757481] m25p80 spi0.0: SPI transfer timed out [ 13.762185] m25p80 spi0.0: error -110 reading 5 [ 13.766703] error -110 reading SR [ 13.770010] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x003787f0, error code: -110. [ 13.780174] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 527, returned error is -110 [ 13.790685] jffs2: Returned error for crccheck of ino #527. Expect badness... [ 14.057481] m25p80 spi0.0: SPI transfer timed out [ 14.062178] m25p80 spi0.0: error -110 reading 5 [ 14.066704] error -110 reading SR [ 14.070012] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x0060c654, error code: -110. [ 14.080176] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 783, returned error is -110 [ 14.090687] jffs2: Returned error for crccheck of ino #783. Expect badness... [ 14.357480] m25p80 spi0.0: SPI transfer timed out [ 14.362179] m25p80 spi0.0: error -110 reading 5 [ 14.366696] error -110 reading SR [ 14.370004] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x0061162c, error code: -110. [ 14.380168] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 911, returned error is -110 [ 14.390679] jffs2: Returned error for crccheck of ino #911. Expect badness... [ 14.657476] m25p80 spi0.0: SPI transfer timed out [ 14.662180] m25p80 spi0.0: error -110 reading 5 [ 14.666706] error -110 reading SR [ 14.670014] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x006ac754, error code: -110. [ 14.680178] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 1039, returned error is -110 [ 14.690776] jffs2: Returned error for crccheck of ino #1039. Expect badness... [ 14.957482] m25p80 spi0.0: SPI transfer timed out [ 14.962181] m25p80 spi0.0: error -110 reading 5 [ 14.966701] error -110 reading SR [ 14.970007] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x008ec414, error code: -110. [ 14.980171] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 1167, returned error is -110 [ 14.990768] jffs2: Returned error for crccheck of ino #1167. Expect badness... [ 15.257481] m25p80 spi0.0: SPI transfer timed out [ 15.262182] m25p80 spi0.0: error -110 reading 5 [ 15.266700] error -110 reading SR [ 15.270008] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x001198fc, error code: -110. [ 15.280172] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 272, returned error is -110 [ 15.290683] jffs2: Returned error for crccheck of ino #272. Expect badness... [ 15.557481] m25p80 spi0.0: SPI transfer timed out [ 15.562183] m25p80 spi0.0: error -110 reading 5 [ 15.566701] error -110 reading SR [ 15.570009] jffs2: error: (2062) jffs2_get_inode_nodes: can not read 40 bytes from 0x002cf024, error code: -110. [ 15.580173] jffs2: error: (2062) jffs2_do_read_inode_internal: cannot read nodes for ino 400, returned error is -110 [ 15.590684] jffs2: Returned error for crccheck of ino #400. Expect badness...