13.1 Known Issues:
(Xilinx Answer 42682)Design Advisory for Virtex-6 - 13.x iMPACT - eFUSE Key Programming Incorrect when Target FPGA is not the Only Device in the JTAG Chain
(Xilinx Answer 40505) 13.x iMPACT - "Close Others" option for a Tab does not work correctly
(Xilinx Answer 37348) 12.x/13.1 iMPACT - PROM File Formatter - When I generate an MCS including a ".mem" or ".elf" file my system does not boot or the data is not distributed as expected in the flash
(Xilinx Answer 39543) 12.x/13.1 iMPACT - "Verify Succeeded" is reported even the CPLD is blank
(Xilinx Answer 40561) 13.1 iMPACT - SVF file reports incorrect position for devices
(Xilinx Answer 40061) 12.x/13.x iMPACT - Does iMPACT save your cable speed in the project file?
(Xilinx Answer 40562) 12.x/13.x iMPACT - Virtex-6 - Indirect BPI core upper address bits clash with VREF pins
(Xilinx Answer 40563) 12.x/13.x- iMPACT - Supported 18V00 Devices - INFO:iMPACT:583
(Xilinx Answer 41555) 13.1 iMPACT - SVF files do not use " STATE RESET" for Virtex-6
(Xilinx Answer 41704) iMPACT - Customer survey pops up every time I open iMPACT
(Xilinx Answer 41633)13.1 IMPACT - PROM File Formatter wizard generates wrong PROM file (MCS/BIN... etc) for Spartan-3AN ISF memory for Revision One
(Xilinx Answer 40610) 12.x/13.x iMPACT - When I do a verify with Indirect programming of my BPI flash fails if user data is present
(Xilinx Answer 41808) iMPACT 13.x - Parallel Cable IV speed cannot be modified
(Xilinx Answer 42557)13.x iMPACT - Spartan-3AN - Multiboot MCS File Generation and BitGen Settings for default addressing mode
(Xilinx Answer 43147) 13.x iMPACT - STAPL files created on Linux for compressed bit files are incorrect
(Xilinx Answer 44502)13.x iMPACT - INFO:iMPACT - The selected file's size (xxxxxxxxxxx bits) is larger than devices supported in this mode.
(Xilinx Answer 44503)13.2 iMPACT - Cable Driver Install - Jungo driver installation fails on SUSE 11
(Xilinx Answer 42512)13.x iMPACT - Indirect programming with Digilent cable causes iMPACT to crash
13.2 Resolved Issues:
(Xilinx Answer 41633)13.1 IMPACT - PROM File Formatter wizard generates wrong PROM file (MCS/BIN... etc) for Spartan-3AN ISF memory for Revision One
(Xilinx Answer 39543) 12.x/13.1 iMPACT - "Verify Succeeded" is reported even the CPLD is blank
(Xilinx Answer 41704) iMPACT - Customer survey pops up every time I open iMPACT
13.2 Known Issues:
(Xilinx Answer 42682)Design Advisory for Virtex-6 - 13.x iMPACT - eFUSE Key Programming Incorrect when Target FPGA is not the Only Device in the JTAG Chain
(Xilinx Answer 42728) 13.2 iMPACT/ChipScope/XMD - Digilent programming cable requires the LibUSB1.0 package to be installed
(Xilinx Answer 42943) 13.2 iMPACT - PROM file formatter incorrectly shows the XCF128XL as a supported PROM for 7-series
(Xilinx Answer 42852) 13.x iMPACT - There is a leading '0' when a Platform flash checksum is read through impact
(Xilinx Answer 40610) 12.x/13.x iMPACT - When I do a verify with Indirect programming of my BPI flash fails if user data is present
(Xilinx Answer 40561) 13.1 iMPACT - SVF file reports incorrect position for devices
(Xilinx Answer 40061) 12.x/13.x iMPACT - Does iMPACT save your cable speed in the project file?
(Xilinx Answer 41555) 13.1 iMPACT - SVF files do not use " STATE RESET" for Virtex-6
(Xilinx Answer 40562) 12.x/13.x iMPACT - Virtex-6 - Indirect BPI core upper address bits clash with Vref pins
(Xilinx Answer 40563) 12.x/13.x- iMPACT - Supported 18V00 Devices - INFO:iMPACT:583
(Xilinx Answer 41633)13.1 IMPACT - PROM File Formatter wizard generates wrong PROM file (MCS/BIN... etc.) for Spartan-3AN ISF memory for Revision One
(Xilinx Answer 41808) iMPACT 13.x - Parallel Cable IV speed can't be modified
(Xilinx Answer 42557)13.x iMPACT - Spartan-3AN - Multiboot MCS File Generation and BitGen Settings for default addressing mode
(Xilinx Answer 43147) 13.x iMPACT - STAPL files created on Linux for compressed bit files are incorrect
(Xilinx Answer 43148) 13.2 iMPACT - iMPACT crashes when performing Remote Indirect Flash programming operations
(Xilinx Answer 43149) 13.2 iMPACT - Specifying 12 MHz as Cable frequency results in "WARNING:iMPACT - Unsupported frequency. Using default frequency: 6 MHz"
(Xilinx Answer 43150) 13.2 iMPACT - Programming reported as successful even though there are configuration errors in the Status Register
(Xilinx Answer 44498)13.2 iMPACT - Erase properties for my CPLD show a CFGBVS dropdown box, what is this?
(Xilinx Answer 44502)13.x iMPACT - INFO:iMPACT - The selected file's size (xxxxxxxxxxx bits) is larger than devices supported in this mode
(Xilinx Answer 44397)13.x iMPACT - Cable Driver Installation - Installation passes on Windows 7 but the Jungo driver Windrvr6 does not operate or appear in the device manager
(Xilinx Answer 44421)Design Advisory for 13.2 iMPACT - Incorrect indirect programming core file is loaded to Kintex-7 leading to potential device damage
(Xilinx Answer 42512)13.x iMPACT - Indirect programming with Digilent cable causes iMPACT to crash
13.3 Resolved Issues:
(Xilinx Answer 42943) 13.2 iMPACT - PROM file formatter incorrectly shows the XCF128XL as a supported PROM for 7-series
(Xilinx Answer 44498)13.2 iMPACT - Erase properties for my CPLD show a CFGBVS dropdown box, what is this?
(Xilinx Answer 42557)13.x iMPACT - Spartan-3AN - Multiboot MCS File Generation and BitGen Settings for default addressing mode
(Xilinx Answer 43149) 13.2 iMPACT - Specifying 12 MHz as Cable frequency results in "WARNING:iMPACT - Unsupported frequency. Using default frequency: 6 MHz"
(Xilinx Answer 44502)13.x iMPACT - INFO:iMPACT - The selected file's size (xxxxxxxxxxx bits) is larger than devices supported in this mode
(Xilinx Answer 44503)13.2 iMPACT - Cable Driver Install - Jungo driver installation fails on SUSE 11
(Xilinx Answer 44421)Design Advisory for 13.2 iMPACT - Incorrect indirect programming core file is loaded to Kintex-7 leading to potential device damage
13.3 Known Issues:
(Xilinx Answer 42682)Design Advisory for Virtex-6 - 13.x iMPACT - eFUSE Key Programming Incorrect when Target FPGA is not the Only Device in the JTAG Chain
(Xilinx Answer 40563) 12.x/13.x- iMPACT - Supported 18V00 Devices - INFO:iMPACT:583
(Xilinx Answer 41555) 13.x iMPACT - SVF files do not use " STATE RESET" for Virtex-6
(Xilinx Answer 40061) 12.x/13.x iMPACT - Does iMPACT save your cable speed in the project file?
(Xilinx Answer 40561) 13.x iMPACT - SVF file reports incorrect position for devices
(Xilinx Answer 40610) 12.x/13.x iMPACT - When I do a verify with Indirect programming of my BPI flash fails if user data is present
(Xilinx Answer 42852) 13.x iMPACT - There is a leading '0' when a Platform flash checksum is read through impact
(Xilinx Answer 42728) 13.x iMPACT/ChipScope/XMD - Digilent programming cable requires the LibUSB1.0 package to be installed
(Xilinx Answer 43147) 13.x iMPACT - STAPL files created on Linux for compressed bit files are incorrect
(Xilinx Answer 43148) 13.x iMPACT - iMPACT crashes when performing Remote Indirect Flash programming operations
(Xilinx Answer 43150) 13.x iMPACT - Programming reported as successful even though there are configuration errors in the Status Register
(Xilinx Answer 44397)13.x iMPACT - Cable Driver Installation - Installation passes on Windows 7 but the Jungo driver Windrvr6 does not operate or appear in the device manager
(Xilinx Answer 42512)13.x iMPACT - Indirect programming with Digilent cable causes iMPACT to crash
(Xilinx Answer 45346)13.3 iMPACT - Virtex-7 - Indirect BPI Programming fails with "Core is not loaded"
13.4 Known Issues:
(Xilinx Answer 42682)Design Advisory for Virtex-6 - 13.x iMPACT - eFUSE Key Programming Incorrect when Target FPGA is not the Only Device in the JTAG Chain
(Xilinx Answer 40563) 12.x/13.x- iMPACT - Supported 18V00 Devices - INFO:iMPACT:583
(Xilinx Answer 41555) 13.x iMPACT - SVF files do not use " STATE RESET" for Virtex-6
(Xilinx Answer 40061) 12.x/13.x iMPACT - Does iMPACT save your cable speed in the project file?
(Xilinx Answer 40561) 13.x iMPACT - SVF file reports incorrect position for devices
(Xilinx Answer 40610) 12.x/13.x iMPACT - When I do a verify with Indirect programming of my BPI flash fails if user data is present
(Xilinx Answer 42852) 13.x iMPACT - There is a leading '0' when a Platform flash checksum is read through impact
(Xilinx Answer 42728) 13.x iMPACT/ChipScope/XMD - Digilent programming cable requires the LibUSB1.0 package to be installed
(Xilinx Answer 43147) 13.x iMPACT - STAPL files created on Linux for compressed bit files are incorrect
(Xilinx Answer 43148) 13.x iMPACT - iMPACT crashes when performing Remote Indirect Flash programming operations
(Xilinx Answer 43150) 13.x iMPACT - Programming reported as successful even though there are configuration errors in the Status Register
(Xilinx Answer 44397)13.x iMPACT - Cable Driver Installation - Installation passes on Windows 7 but the Jungo driver Windrvr6 does not operate or appear in the device manager
(Xilinx Answer 42512)13.x iMPACT - Indirect programming with Digilent cable causes iMPACT to crash
(Xilinx Answer 45346)13.3 iMPACT - Virtex-7 - Indirect BPI Programming fails with "Core is not loaded"
(Xilinx Answer 45560) 13.x iMPACT - Verify fails with "INFO:iMPACT:395 - The number of difference is -1"
(Xilinx Answer 45809)13.x iMPACT - LabTools - iMPACT crashes when I attempt to program a Zynq xc7z020 device
(Xilinx Answer 46404)13.4 iMPACT - When attempting to Erase or Program a 28f00ag18f flash I see errors
(Xilinx Answer 46687) 13.4 iMPACT - Batch Mode -Using setcablespeed before setcable causes iMPACT to crash
(Xilinx Answer 46836)13.4 iMPACT - Kintex-7 - XC7K420T patch and Known Issues