This answer record contains the Release Notes for the LogiCORE IP Tri-Mode Ethernet MAC Core and includes the following:
For installation instructions, general CORE Generator software known issues, and design tools requirements, see the IP Release Notes Guide.
New Features in v5.5 Core
Supported Devices in v5.5 Core
Note: For a complete part and package support list, please check the Xilinx CORE Generator interface (under 'Supported Families') for the Tri-Mode Ethernet MAC Core.
For the previous version "New Features" and "Supported Devices", see the readme.txt or version information file available with the generated core.
General Known Issues
This table correlates the core version to the first ISE or Vivado design tools release version in which it was included.
| Core Version | ISE Tools Version | Vivado Tools Version |
| v5.5 | ISE 14.4 | 2012.4 |
| v5.4 | ISE 14.2 | 2012.2 |
| v5.3 | ISE 14.1 | 2012.1 |
| v5.2 | ISE 13.4 | NA |
| v5.1 | ISE 13.1 | NA |
The following table provides known issues for the Tri-Mode Ethernet MAC core, starting with v5.1, initially released in ISE Design Suite 13.1.This is the first version to support 7 series devices and have an AXI interface. For earlier versions of the core using the legacy user interface, please refer to the IP Release Notes Guide for the release notes answer record by version.
Note: The "Version Found" column lists the version the problem was first discovered. The problem might also exist in earlier versions, but no specific testing has been performed to verify earlier versions.
| (Xilinx Answer 54785) | IFG Adjust values smaller than 9 not used when core is generated with half duplex support | v5.5 | v6.0 |
| (Xilinx Answer 53360) | Multiple pause frame requests can result in a corrupted pause quanta being output | v5.4 | v5.5 |
| (Xilinx Answer 52556) | Frames within 12 bytes of the max frame size could get marked bad | v5.4 | v5.5 |
| (Xilinx Answer 53521) | RGMII_TX_ER incorrect timing at 10/100 speeds | v5.4 | v5.5 |
| (Xilinx Answer 53520) | Very Small Runt frames can be incorrectly marked good | v5.4 | v5.5 |
| (Xilinx Answer 40028) | Virtex-6 FPGAs - Meeting GMII and RGMII setup and hold times | v5.1 | N/A |
| (Xilinx Answer 35336) | Spartan-6 FPGAs - Meeting GMII setup and hold times | v5.1 | N/A |
| (Xilinx Answer 50860) | ISE - 7-Series - Input Timing Violations may be seen in the Example design | v5.4 | v5.5 |
| (Xilinx Answer 50321) | VHDL - 1G - RGMII - BUFGMUX Instantiation Results in Synthesis Errors | v5.3 | v5.4 |
| (Xilinx Answer 47896) | address_decode.v errors out during Synplify Synthesis | v5.3 | v5.4 |
| (Xilinx Answer 47700) | Invalid Reads from the AVB PTP Tx Buffer | v5.2 | v5.3 |
| (Xilinx Answer 45527) | UCF changes needed to target KC705 RevC/RevD | v5.1 | v5.3 |
| (Xilinx Answer 45724) | Targeting Spartan-6 and Virtex-6 Q-grade devices | v5.1 | v5.3 |
| (Xilinx Answer 46167) | Example Design UCF and Implementation Scripts are missing | v5.2 | v5.2rev1 |
| (Xilinx Answer 42847) | Example Design fail in BitGen when targeting Virtex-7 or Kintex-7 devices | v5.1 | v5.2 |
| (Xilinx Answer 42089) | ERROR:NgdBuild:973 - The temac symbol is not supported | v5.1 | v5.2 |
| (Xilinx Answer 42926) | Error Invalid target device when running 7-Series Example design in 13.2 | v5.1 | v5.2 |
Vivado Design Suite Specific Known Issues
| (Xilinx Answer 54165) | Timing failure seen when core generated without address filter | v5.5 | not resolved |
| (Xilinx Answer 54163) | Windows - core xdc file is not correctly loaded after opening the Implemented design | v5.5 | not resolved |
| Ethernet AVB option not supported in Vivado Design Suite 2012.1 | |||
| Vivado - Guidance for Simulating Ethernet IP cores |
| Answer Number | 问答标题 | 问题版本 | 已解决问题的版本 |
|---|---|---|---|
| 47733 | LogiCORE IP Tri-Mode Ethernet MAC v5.3 - Ethernet AVB option not supported in Vivado Design Suite 2012.1 | N/A | N/A |
| AR# 47695 | |
|---|---|
| 日期 | 03/06/2013 |
| 状态 | Active |
| Type | 版本说明 |
| IP | |